2022 Current NACE-CIP1-001 dumps Preparation through Our Practice Test [Q53-Q70]

4/5 - (1 vote)

2022 Current NACE-CIP1-001 dumps Preparation through Our Practice Test

100% Reliable Microsoft NACE-CIP1-001 Exam Dumps Test Pdf Exam Material

Learn how to register for NACE CIP1-001 Certification.

The candidate must visit the official website of the NACE CIP1-001 exam. You need to provide all the required details in the application form. You will receive an email from us after filling the registration form. We will send you the NACE CIP1-001 examination kit. You can easily download the NACE CIP1-001 exam dumps to prepare for the NACE CIP1-001 exam.

QUESTION 53
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?

Yes, because the ‘two standards are not equivalent

No, because there is no real difference in the standards

It depends on which hand tool the Contractor selects

It depends on which power tool the Contractor selects

QUESTION 54
The Inspector should record the serial numbers of inspection instruments:

Only if the specification requires it

Each time the instrument is used

Only if the instrument is suspected of not working properly

Only when verifying accuracy of the instrument

QUESTION 55
An Inspector should change position when:

The Inspector is convinced by verifiable facts

Only when directed by the supervisor

The Inspectors position is not the majority position

The Owner can save some money by the change

QUESTION 56
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a

dry film thickness (DEI) measurement.

wet film thickness (WFT) measurement.

blotter test for the presence of oil and water.

vial lest.

QUESTION 57
As a NACE Coating Inspector your responsibility with respect to safety is to:

Assume the role of the Safety Inspector

Check the PPE used by the Applicators

Act in accordance with the site safety requirements and set an example

Check the credentials of the Safety Officer on site

QUESTION 58
Check abrasive blast pressure with a

needle pressure gauge

replica tape

surface comparator

nozzle aperature gauge

QUESTION 59
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:

telegraphing.

monitoring

juxtaposing.

transitioning.

QUESTION 60
Prior to using Inspection Tools the inspector must:

Ensure the instrument is within calibration parameters

Be trained on how to use the instrument

Read the manufactures’ instructions

a), b) & c)

QUESTION 61
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT

what items were coated.

what materials were used.

when the coating will be reapplied.

how the item was coated.

QUESTION 62
Stripe coats are generally applied to:

Edges and corners

Welds

Complex geometric shapes

a), b), and c)

QUESTION 63
Upon arrival of coating materials, the inspector should

review coating contractors’ plans for storage of coating materials and confirm they meet national, local and owners’ fire and environmental regulations.

observe and document the amount of material and batch numbers.

observe aryl document that the applicator WFT at regular intervals during application.

observe and document time frame and environmental conditions between each coat.

QUESTION 64
ISO SA 2 is defined as:

Near White Metal Blasting

Thorough Blast Cleaning

Very Thorough Blast Cleaning

Light Blast Cleaning

QUESTION 65
ISO SA 3 is directly equivalent to:

NACE No. 1/SSPC SP 5

NACE No. 2/SSPC SP 10

NACE No. 3/SSPC SP 6

None of the above

QUESTION 66
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?

105 Gauge Readings resulting in 35 Spot Measurements

75 Gauge Readings resulting in 25 Spot Measurements

225 Gauge Readings resulting in 75 Spot Measurements

45 Gauge readings resulting in 15 Spot Measurements

QUESTION 67
When applying Thermal Spray Coatings the specification is most likely to refence:

SSPC PA 2

NACE SP 0178

NACE SP 0188

SSPC-CS 23.00/AWS C2.23/NACE No. 12

QUESTION 68
ISO ST 3 is described as:

Thorough hand tool cleaning

Very Thorough power tool cleaning