[2025] 300-425 Exam Dumps, Test Engine Practice Test Questions [Q124-Q144]

NEW QUESTION 124
Which protocol is used in a DMVPN network to map physical IP addresses to logical IP addresses?

BGP

LLDP

EIGRP

NHRP

NEW QUESTION 125
A wireless engineer is hired to design a network for a technology company. The company campus has four buildings and a warehouse with access points that provide full wireless coverage as well as a pair of WLCs located in the core of the network. Which type of wireless architecture is being used?

unified deployment

autonomous deployment

centralized deployment

distributed deployment

NEW QUESTION 126
A rapidly expanding company has tasked their network engineer with wirelessly connecting a new cubicle area with Cisco workgroup bridges until the wired network is complete. Each of 42 new users has a computer and VoIP phone. How many APs for workgroup bridging must be ordered to keep cost at a minimum while connecting all devices?

4

5

6

7

NEW QUESTION 127
A customer has a central Cisco WLC that manages APs in FlexConnect mode. The wireless infrastructure supports multiple small branches. One branch deploys new CCX wireless phones that are authenticated by a central Cisco ISE via PEAP/IMSCHAPv2, and traffic is switched locally. The customer must reduce the number of full authentication requests and optimize roaming for the new phones. Which action accomplishes the requirement?

Enable CCKM on the voice SSID and add APs to a FlexConnect group.

Enable Aironet IE on the voice SSID and add APs to an AP group.

Enable Aironet IE on the voice SSID and add APs to a FlexConnect group.

Enable CCKM on the voice SSID and add APs to an AP group.

NEW QUESTION 128
Drag and Drop Question
A wireless consultant is creating a wireless design for a multistory building. The building will house several groups that will use the wireless network for different operations. Depending on how the wireless network is used, different wireless approach designs must be taken. Drag and drop the services from the left onto the AP density levels on the right based on the wireless deployment requirements.

NEW QUESTION 129
A wireless network consists of:
– two IOS XE controllers installed in a data center
– 9100 series APs
– corporate and a guest WLAN
The customer must high availability pair two Cisco WLCs for the client SSO. Which two design approaches must the engineer take to meet the requirement? (Choose two.)

The controllers must have the same number of licenses.

Both WLCs must have the same redundancy management IP address.

Both WLCs must have the same service port IP address.

Each WLC must have a unique redundancy management IP address.

The controllers must run the same operating system version.

NEW QUESTION 130
A customer has determined that aesthetics is a primary concern for their upcoming guest deployment. Which design consideration can be leveraged to address this concern?

Paint the access point to cover the LED from being noticeable.

Use enclosures to hide the wireless infrastructure in the surrounding environment.

Use AIR-AP-BRACKET-1 to allow for greater mounting locations

Deploy environmentally friendly cabling components to blend into the environment.

NEW QUESTION 131
Refer to the exhibit.

Which two statements about Cisco Prime Infrastructure are true? (Choose two.)

It presents the recommended number of APs for the selected coverage area based on the selections made.

Planning mode requires a special license in Cisco Prime Infrastructure.

It shows the map editor feature in Cisco Prime Infrastructure.

Controllers must be synchronized with Cisco Prime Infrastructure for planning mode to work.

It shows the planning mode feature in Cisco Prime Infrastructure.

NEW QUESTION 132
A company is in the process of relocating to a new force space and ends out that the Internet circuit will not be ready before the move. The new building has a non-Cisco WLAN to which they can connect. The engineer has a 12-port switch and one Cisco autonomous AP and must connect multiple wired devices. Which additional device is needed to get all clients connected over the workgroup bridge?

router

transparent firewall

hub

wireless controller

NEW QUESTION 133
An engineer is working on a wireless refresh for a customer and identified that the existing WLCs have RTU licenses installed. Which two WLC models can reuse the licenses? (Choose two.)

5520

vWLC

3504

5508

2504

NEW QUESTION 134
An engineer is designing a point-to-multipoint mesh network. Which two AP configurations must be completed for a site survey? (Choose two.)

MAP hostnames

Rx power

mesh on 2.4 GHz band

bridge group name

Tx power

NEW QUESTION 135
An engineer is designing a wireless network that will support many different types of wireless clients. When conducting the survey, which client must be used to ensure a consistent experience for all of the wireless clients?

the client that has the highest RF properties

the client that is used most by the company

the client that is used least by the company

the client with the worst RF characteristics

NEW QUESTION 136
A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)

The coverage area must have a noise floor that does not exceed -87 dBm.

The client device must have at least an -67 dBm RSSI.

The rate of retransmitted packets must be 15 percent or below.

The rate of retransmitted packets must be 20 percent or below.

The client device must have at least an -65 dBm RSSI.

NEW QUESTION 137
Clustering Cisco WLCs into a single RF group enables the RRM algorithms to scale beyond the capabilities of a single Cisco WLC. How many WLC and APs in an RF group can the controller software scale up to in WLC release 8.9 depending on the platform?

up to 20 WLCs and 1000 APs

up to 20 WLCs and 3000 APs

up to 20 WLCs and 4000 APs

up to 20 WLCs and 6000 APs

NEW QUESTION 138
Refer to the exhibit. A company is designing a Cisco wireless solution that has two WLCs named WLC1 and WLC2 and several APs. An AP named AP12 is a critical AP and is provisioned to be installed in hallway 6, which is located just outside the office of the company director and must always connect to WLC1. Which priority level must be incorporated in the design for AP12?

1

2

3

4

NEW QUESTION 139
An engineer is trying to configure the APs installed in a new auditorium to use 40 MHz channels with high data rates and lower TX power. The APs in the building hallway must use lower-density design settings configured for the rest of the building. Which two configurations achieve this design? (Choose two.)

TPC

DCA

AP group

RRM

RF protocol

NEW QUESTION 140
An engineer is designing a wireless network to support Cisco Hyperlocation. The customer indicated some How is the design adjusted?

Add additional APs to all the comers of the site.

Add more APs than indicated from the site survey spread across all areas.

Add an additional AP in the middle of the dense area.

Run the site survey using -57d Bm as a threshold.

NEW QUESTION 141
Why is 802.11a connectivity reduced in an X-ray room?

X-rays create significant non-Wi-Fi interference on the 802.11a band.

X-rays impact the 802,11a UNll-2 channels that cause access points to dynamically change channels.

X -rays within these rooms cause multipath issues.

X-ray rooms exhibit increased signal attenuation.

NEW QUESTION 142
An engineer is upgrading the legacy APs to 802.11ac Wave 2 capable APs. The existing gigabit uplinked switches provide 802.3at. Which switch limitation is a concern?

interface throughput

high availability

collision domains

output power

NEW QUESTION 143
An engineer changed me TPC Power Threshold for a wireless deployment from the default value to 65 dBm. The engineer conducts a new post deployment survey to validate the results.
What is the expected outcome?

increased received sensitivity

decreased channel overlap

decreased client signal strength

increased cell size

NEW QUESTION 144
A network engineer is working on a predictive WLAN design, the new wireless network must support access to Internet, email, voice, and the inventory database, to successfully support these services, which configuration must the engineer use for the signal strength levels and SNR on the planning tool?

signal strength of -67 dBm, 25-dB SNR, and maximum 1 percent packet loss.

signal strength of -67 dBm, 20-dB SNR, and maximum 5 percent, packet loss.

signal strength of 67 dBm, 20-dB SNR, and maximum 1 percent packet loss.

signal strength of-70 dBm,30-dB SNR. and maximum 10 percent packet loss.