[Oct 23, 2024] Latest Aruba Certified Professional HPE7-A01 Actual Free Exam Questions [Q65-Q85]

NEW QUESTION 65
Using Aruba best practices what should be enabled for visitor networks where encryption is needed but authentication is not required?

Wi-Fi Protected Access 3 Enterprise

Opportunistic Wireless Encryption

Wired Equivalent Privacy

Open Network Access

NEW QUESTION 66
With the Aruba CX 6100 48G switch with uplinks of 1/1/47 and 1/1/48. how do you automate the process of resuming the port operational state once a loop on a client port is cleared?

Configure int 1/1/1-1/1/52 loop-protect disable timer.

Configure global loop-protect disable timer.

Configure int 1/1/1-1/1/46 loop-protect re-enable-timer.

Configure global loop-protect re-enable-timer.

NEW QUESTION 67
What steps are part of the Key Management workflow when a wireless device is roaming from AP1 to AP2?
(Select two.)

AP1 will cache the client’s information and send it to the Key Management service

The Key Management service receives from AirMatch a list of all AP2’s neighbors

The Key Management service receives a list of all AP1 s neighbors from AirMatch.

The Key Management service then generates R1 keys for AP2’s neighbors.

A client associates and authenticates with the AP2 after roaming from AP1

NEW QUESTION 68
Which component is used by the Aruba Network Analytics Engine (NAE)?

JSON-based scripts

Lisp-based agents

Ruby-based scripts

Current State Database

NEW QUESTION 69
Refer to Exhibit:

With Access-1, What needs to be identically configured With MSTP to load-balance VLANS?

Spanning-tree bpdu-guard setting

Spanning-tree instance vlan mapppjng

spanning-tree Cist mapping

Spanning-tree root-guard setting

The correct answer is B. Spanning-tree instance VLAN mapping.
To load-balance VLANs with MSTP, you need to configure the same VLAN-to-instance mapping on all switches in the same MST region. This means that you need to assign different VLANs to different MST instances, and then adjust the spanning tree parameters (such as priority, cost, or port role) for each instance to achieve the desired load balancing. For example, you can make one switch the root for instance 1 and another switch the root for instance 2, and then map half of the VLANs to instance 1 and the other half to instance 2.
According to the Cisco documentUnderstand the Multiple Spanning Tree Protocol (802.1s), one of the steps to configure MST is:
* Split your set of VLANs into more instances and configure different MST settings for each of these instances. In order to easily achieve this, elect Bridge D1 to be the root for VLANs 501 through 1000, and Bridge D2 to be the root for VLANs 1 through 500. These statements are true for this configuration:
Switch D1(config)#spanning-tree mst configuration
Switch D1(config-mst)#instance 1 vlan 501-1000
Switch D1(config-mst)#exit
Switch D1(config)#spanning-tree mst 1 priority 0
Switch D2(config)#spanning-tree mst configuration
Switch D2(config-mst)#instance 2 vlan 1-500
Switch D2(config-mst)#exit
Switch D2(config)#spanning-tree mst 2 priority 0
The above commands create two MST instances, 1 and 2, and map VLANs 501-1000 to instance 1 and VLANs 1-500 to instance 2. Then, they make switch D1 the root for instance 1 and switch D2 the root for instance 2.
The other options are incorrect because:
* A. Spanning-tree bpdu-guard setting is a security feature that disables a port if it receives a BPDU from an unauthorized device. It does not affect load balancing with MSTP.
* C. Spanning-tree CIST mapping is not a valid command. CIST stands for Common and Internal Spanning Tree, which is the spanning tree instance that runs within an MST region and interacts with other regions or non-MST switches.
* D. Spanning-tree root-guard setting is another security feature that prevents a port from becoming a root port if it receives superior BPDUs from another switch. It does not affect load balancing with MSTP.

NEW QUESTION 70
Your customer is interested in hearing more about how roles can help keep consistent policy enforcement in a distributed overlay fabric How would you explain this concept to them”

Group Based Policy ID is applied on egress VTEP after device authentication and policy is enforced on ingress VTEP

Role-based policies are tied to IP addresses which have an advantage over IP-based policies and role names are sent between VTEPs

Group Based Policy ID is applied on ingress VTEP after device authentication and policy is enforced on egress VTEP

Role-based policies enhance User Based Tunneling across the campus network and the policy traffic is protected with iPsec

NEW QUESTION 71
Two AOS-CX switches are configured with VSX at the the Access-Aggregation layer where servers attach to them An SVI interface is configured for VLAN 10 and serves as the default gateway for VLAN 10. The ISL link between the switches fails, but the keepalive interface functions. Active gateway has been configured on the VSX switches.

What is correct about access from the servers to the Core? (Select two.)

Server 1 can access the core layer via the keepalrve link

Server 2 can access the core layer via the keepalive link

Server 2 cannot access the core layer.

Server 1 can access the core layer via both uplinks

Server 1 and Server 2 can communicate with each other via the core layer

Server 1 can access the core layer on only one uplink

NEW QUESTION 72
Refer to the image.

Your customer is complaining of weak Wi-Fi coverage in their office. They mention that the office on the other side of the hall has much better signal.
What is the likely cause of this issue7

The AP is a remote access point.

The AP is using a directional antenna.

The AP is an outdoor access point.

The AP is configured in Mesh mode

NEW QUESTION 73
The customer needs a network hardware refresh to replace an aging Aruba 5406R core switch pair using spanning tree configuration with Aruba CX 8360-32YC switches What is the benefit of VSX clustering with the new solution?

stacked data-plane

faster MSTP converge processing

dual Aruba AP LAN port connectivity for PoE redundancy

dual control plane provides better resiliency

NEW QUESTION 74
A customer is using stacked Aruba CX 6200 and CX 6300 switches for access and a VSX pair of Aruba CX 8325 as a collapsed core 802.1X is implemented for authentication. Due to the lack of cabling, some unmanaged switches are still in use Sometimes devices behind these switches cause network outages. The switch should send a warning to the helpdesk when the problem occurs. You have been asked to implement an effective solution to the problem.
What is the solution for this?

Configure spanning tree on the Aruba CX 8325 switches Set the trap-option

Configure loop protection on all edge ports of the Aruba CX 6200 and CX 6300 switches No trap option is needed

Configure loop protection on all edge ports of the Aruba CX 6200 and CX 6300 switches Set up the trap-option

Configure spanning tree on the Aruba CX 6200 and CX 6300 switches No trap option is needed

NEW QUESTION 75
Drag and Drop Question
Match the topics of an AOS10 Tunneled mode setup between an AP and a Gateway. (Options may be used more than once or not at all.)

NEW QUESTION 76
Your customer has an Aruba CX 6200F VSF stack with two switches. A third member (JL726A) needs to be added to the VSF configuration.
What e the configuration that enables the new devices to join the VSF?

NEW QUESTION 77
A customer is using stacked Aruba CX 6200 and CX 6300 switches for access and a VSX pair of Aruba CX
8325 as a collapsed core 802 1X is implemented for authentication. Due to the lack of cabling, some unmanaged switches are still in use Sometimes devices behind these switches cause network outages The switch should send a warning to the helpdesk when the problem occurs You have been asked to implement an effective solution to the problem What is the solution for this?

Configure spanning tree on the Aruba CX 8325 switches Set the trap-option

Configure loop protection on all edge ports of the Aruba CX 6200 and CX 6300 switches No trap option is needed

Configure loop protection on all edge ports of the Aruba CX 6200 and CX 6300 switches Set up the trap-option

Configure spanning tree on the Aruba CX 6200 and CX 6300 switches No trap option is needed

NEW QUESTION 78
A network engineer recently identified that a wired device connected to a CX Switch is misbehaving on the network To address this issue, a new ClearPass policy has been put in place to prevent this device from connecting to the network again.
Which steps need to be implemented to allow ClearPass to perform a CoA and change the access for this wired device? (Select two.)

Confirm that NTP is configured on the switch and ClearPass

Configure dynamic authorization on the switch.

Bounce the switchport

Use Dynamic Segmentation.

Configure dynamic authorization on the switchport

NEW QUESTION 79
The administrator notices that wired guest users that have exceeded their bandwidth limit are not being disconnected Access Tracker in ClearPass indicates a disconnect CoA message is being sent to the AOS-CX switch.
An administrator has performed the following configuration

What is the most likely cause of this issue?

Change of Authorization has not been globally enabled on the switch

The SSL certificate for CPPM has not been added as a trust point on the switch

There is a mismatch between the RADIUS secret on the switch and CPPM.

There is a time difference between the switch and the ClearPass Policy Manager

NEW QUESTION 80
A customer is looking Tor a wireless authentication solution for all of their loT devices that meet the following requirements:
– The wireless traffic between the IoT devices and the Access Points
must be encrypted
– Unique passphrase per device
– Use fingerprint information to perform role-based access
Which solutions will address the customer’s requirements? (Select two.)

MPSK and an internal RADIUS server

MPSK Local with MAC Authentication

ClearPass Policy Manager

MPSK Local with EAP-TLS

Local User Derivation Rules

NEW QUESTION 81
You need lo have different routing-table requirements with Aruba CX 6300 VSF configuration Assuming the correct layer-2 VLAN already exists how would you create a new OSPF configuration for a separate routing table?

Create a new OSPF area, and attach VRF name.

Create a new OSPF process ID with vrf name.

Attach a new OSFP process ID with a custom routing table

Attach OSPF process ID in the VRF configuration.

NEW QUESTION 82
What are two advantages of splitting a larger OSPF area into a number of smaller areas? (Select two )

It extends the LSDB

It increases stability

it simplifies the configuration.

It reduces processing overhead.

It reduces the total number of LSAs

NEW QUESTION 83
List the firewall role derivation flow in the correct order

NEW QUESTION 84
Match each PoE power class to Its corresponding 802.3 standard. (Options may he used more than once or not at all)

NEW QUESTION 85
Refer to Exhibit. A company has deployed 200 AP-635 access points. To take advantage of the 6 GHz band, the administrator has attempted to configure a new WPA3-OWE SSID in Central but is not working as expected.

What would be the correct action to fix the issue?