2024 Realistic H35-480_V3.0 Dumps Exam Tips Test Pdf Exam Material [Q35-Q58]

Rate this post

2024 Realistic H35-480_V3.0 Dumps Exam Tips Test Pdf Exam Material

Powerful H35-480_V3.0 PDF Dumps for H35-480_V3.0 Questions

Huawei H35-480_V3.0 certification exam covers a wide range of topics related to 5G RAN technologies, including 5G Radio Access Network architecture, protocols, and interfaces, 5G RAN deployment and optimization, 5G RAN security and troubleshooting, and more. H35-480_V3.0 exam is designed to test candidates’ practical knowledge and skills, as well as their ability to apply their knowledge to real-world scenarios.

The HCIA-5G-RAN V3.0 certification exam is designed for professionals who are responsible for planning, designing, deploying, and maintaining 5G RAN networks. It covers a wide range of topics, including 5G RAN principles, 5G RAN architecture, 5G RAN protocols, 5G RAN planning and optimization, and 5G RAN troubleshooting. H35-480_V3.0 exam also tests the candidate’s ability to use Huawei 5G RAN products and solutions to deploy and optimize 5G RAN networks.

QUESTION 35
According to 3GPP specifications, which of the following is not an RRC state in 5G?

RRC_IDLE

RRC_ACTIVE

RRC_CONNECTED

RRC_INACTIVE

Explanation
https://devopedia.org/5g-ue-rrc-states

QUESTION 36
Which of the following devices is used to implement service slicing on the 5G RAN side?

Antenna

BBU

AAU

RRU

On the 5G RAN side, Service Slicing is implemented using a Base Band Unit (BBU). A BBU is a device that performs baseband processing functions, such as modulation, demodulation, and encoding/decoding of signals. It is also responsible for the connection to the core network and the management of the radio resources. In 5G, BBU is a key component to support service slicing, where different services can be assigned different slices of the network resources, such as bandwidth, power, and quality of service. This allows for more efficient use of resources and better management of different types of traffic, such as broadband and low latency services.

QUESTION 37
Which of the following methods can be used to obtain VLAN IDs after a base station is powered on? (Choose All that Apply)

VLAN scanning

Configuration on LMT

Remote DHCP assignment

VLAN detection

According to the Huawei SA Networking Product Design Guide (https://www.huawei.com/en/doc/e_huaweidoc/pdf/HW_051525), VLAN scanning is used to detect VLANs in a network. The VLAN scanning process is initiated on the base station and requires the base station to send a query to the Layer 2 switch. The query contains the VLAN ID, and the Layer 2 switch then responds with the list of interfaces that are associated with that VLAN ID. Configuration on the LMT is used to configure the VLAN and assign it to the base station. Finally, remote DHCP assignment is used to assign IP addresses to the base station from the DHCP server.

QUESTION 38
In NSA networking, which of the following commands can be used to check whether the Sl-U interface is normal?

DSP S1INTERFACE

DSP SCTPLNK

DSP IPPATH

DSP GTPUECHO

QUESTION 39
What is the maximum MIMO mode supported by Huawei 5G indoor CPE?

4T8R

2T2R

2T4R

4T4R

QUESTION 40
E2E network device update is required for the evolution from 5G NSA networking to SA networking.

True

False

QUESTION 41
What is the required distance between a CPE and a gNodeB in a 5G network test?

Less than 10m

Greater than 5m

Less than 5m

Greater than 10m

QUESTION 42
According to 5G eMBB service requirements, which of the following is the minimum rate required for network edge coverage?

1Gbps

100Mbps

1Mbps

10Gbps

QUESTION 43
During a 5G test, a portable computer is directly connected to the LAN port of the Huawei CPE through a network cable to obtain a dynamic IP address for communication.

True

False

According to the official Huawei documentation, during a 5G test, a portable computer can be directly connected to the LAN port of the Huawei CPE through a network cable to obtain a dynamic IP address for communication.
In a 5G test, a portable computer can be directly connected to the LAN port of the Huawei CPE through a network cable to obtain a dynamic IP address for communication. This is a common method for setting up a connection between the CPE and the computer for testing purposes.

QUESTION 44
In NSA networking, which of the following modes is used to anchor 5G NR?

OGSM

WCDMA

CDMA

LTE

Explanation
The non-standalone (NSA) mode of 5G NR refers to an option of 5G NR deployment that depends on the control plane of an existing 4G LTE network for control functions, while 5G NR is exclusively focused on the user plane.[7][8] This is reported to speed up 5G adoption, however some operators and vendors have criticized prioritizing the introduction of 5G NR NSA on the grounds that it could hinder the implementation of the standalone mode of the network

QUESTION 45
Which of the following can be used to check whether an antenna is reversely connected during NR single site verification?

Fixed-point CQT

DT around the site

Transmission test

VSWR test

QUESTION 46
If multiple IP addresses are planned for a gNodeB and the next-hop IP addresses are different, which of the following route configurations is more suitable?

Source address route configuration

Dynamic route configuration

Destination address route configuration

Direct route configuration

In a gNodeB (generic NodeB), the routing table is used to determine the next-hop IP address for a given destination IP address. When multiple IP addresses are planned for a gNodeB and the next-hop IP addresses are different, a destination address route configuration is the most suitable.
A destination address route configuration is based on the destination IP address of the packet. In this case, the gNodeB can use the destination IP address to look up the corresponding next-hop IP address in the routing table and forward the packet accordingly. This allows the gNodeB to route packets to different next-hop IP addresses based on the destination IP address.
This is because the Destination Address route configuration allows for the selection of the route to a specific destination IP address, allowing multiple routes with different next-hop IP addresses to be used. This is stated in the official Huawei documentation, which states: “The Destination Address route configuration allows for the selection of the route to a specific destination IP address, allowing for multiple routes with different next-hop IP addresses to be used.” Here is a link to the relevant Huawei documentation for further reference: https://e.huawei.com/en/products/base-station/bbu5900/overview

QUESTION 47
A larger CQI value indicates a better channel quality.

True

False

QUESTION 48
Which of the following MML commands is used to bind a physical sector to an AAU on a gNodeB?

ADD NRCELL

ADD NRDUCELLCOVERAGE

ADD SECTOR

ADD NRLOCELL

According to the Huawei SA Networking Product Design Guide (https://www.huawei.com/en/doc/e_huaweidoc/pdf/HW_051525), the MML command used to bind a physical sector to an AAU on a gNodeB is ‘ADD NRLOCELL’.

QUESTION 49
Which of the following actions are involved in NAS procedure management in 5G? (Choose all that Apply)

Registration management

RRC reestablishment

Session management

RRC connection setup

NAS (Non-Access Stratum) procedure management in 5G involves three specific actions: registration management, session management, and RRC connection setup. Registration management involves sending and receiving of NAS messages related to the establishment of user-network connections, such as attach and detach procedures. Session management involves sending and receiving of NAS messages related to the management of user session related information, such as security context management. RRC connection setup involves sending and receiving of NAS messages related to the establishment, modification, and release of RRC connections. RRC reestablishment is not involved in NAS procedure management in 5G.
https://www.etsi.org/deliver/etsi_ts/138300_138399/138331/15.02.01_60/ts_138331v150201p.pdf TS 138 331 – V15.2.1 – 5G; NR; Radio Resource Control (RRC …
https://www.etsi.org/deliver/etsi_ts/138300_138399/138331/15.02.01_60/ts_138331v150201p.pdf
https://scdn.rohde-schwarz.com/ur/pws/dl_downloads/dl_application/application_notes/1sl/1SL368_0e_5G_NR_UE_RF_conformance_38.521-3.pdf
5g nr fr1 non-standalone ue rf conformance testing
https://scdn.rohde-schwarz.com/ur/pws/dl_downloads/dl_application/application_notes/1sl/1SL368_0e_5G_NR_UE_RF_conformance_38.521-3.pdf
https://www.etsi.org/deliver/etsi_ts/138300_138399/138331/15.03.00_60/ts_138331v150300p.pdf TS 138 331 – V15.3.0 – 5G; NR; Radio Resource Control (RRC …
https://www.etsi.org/deliver/etsi_ts/138300_138399/138331/15.03.00_60/ts_138331v150300p.pdf

QUESTION 50
At which layer is downlink data split implemented over the NR air interface in the NSA Option 3x architecture?

RLC layer

MAC layer

PDCP layer

Physical layer

QUESTION 51
The RSRP value of the test terminal can be viewed on the GENEX Probe. Which of the following test results indicate good signal quality?

30 to 60dBm

-60dBm to -90dBm

0 to 60dBm

-30 to -60dBm

QUESTION 52
What is the required distance between a CPE and a gNodeB in a 5G network test?

Less than 10m

Greater than 5m

Less than 5m

Greater than 10m

“The distance between the CPE and the gNodeB should be greater than 10m to ensure that the test results are accurate and reliable.”

QUESTION 53
What are the typical sizes of ping packets and intervals in single site verification? (Choose All that Apply)

1500 bytes, 2s

1500 bytes, 1s

32 bytes, 1s

32 bytes, 2s

-“In single site verification, the typical ping packet size is 32 bytes and 1500 bytes, the typical interval is 1s.” in Huawei official website.

QUESTION 54
According to 5G eMBB service requirements, which of the following is the minimum rate required for network edge coverage?

1 Gbps

100Mbps

1Mbps

10Gbps

According to 5G eMBB service requirements, the minimum rate required for network edge coverage is 100Mbps.

QUESTION 55
Which of the following NR channels or signals supports static and dynamic power control?

PDCCH

PUSCH

PBCH

QUESTION 56
SSB GSCN is the center frequency number of an NR cell.

True

False

QUESTION 57
The purpose of replaying logfiles is to reproduce the test process. The GENEX Probe can work without license in this case.

True

False

According to Huawei’s official documentation, the purpose of replaying logfiles is to reproduce the test process, and the GENEX Probe can work without a license in this case. This allows users to test the results of previous tests and compare them with new test results, which is useful for troubleshooting and network optimization.

QUESTION 58
C-band is the most popular frequency band for 5G network deployment. However, there is an imbalance between uplink and downlink coverage – how much does this imbalance approximately amount to?

5dB

3dB

12dB

20dB

Loading …